The short answer: yes. Two-part solid surface adhesive such as our iSeam Pro 67 comes in a twin-barrel 50 ml cartridge with a 10:1 mix ratio, so it needs a 10:1 dispensing gun. An ordinary single-tube caulking gun will not do the job. The gun adds about £15 to your first purchase, and you only buy it once. This post is for DIYers, kitchen fitters and small workshops who are about to make a seam in Corian or another solid surface and want to know the real cost before they start.

Why can't you use a normal caulking gun?
A standard caulking gun pushes a single plunger into a single tube. A two-part adhesive has two chambers: the adhesive (Part A) and the activator (Part B). They have to be pushed out together, in the right proportion, and meet only inside the static mixer nozzle. For iSeam Pro 67 that proportion is 10:1 by weight, as set out in the iSeam Pro 67 technical data sheet.
A 10:1 gun has plungers sized to match the cartridge, so each chamber empties at the right rate. That is what gives you a correctly mixed bead from the first squeeze to the last. If the mix is wrong, the adhesive may not cure properly, and that is the one thing you cannot fix once the seam is closed.
How much does the gun cost?
Here are our current prices (checked November 2026):
| Item | Price | What you get |
|---|---|---|
| iSeam Pro 67, Glacier White, 50 ml | £9.00 | Cartridge, supplied with 2 nozzles. Gun not included. |
| 50/75 ml 10:1 manual dispenser | £15.00 | The gun. Buy once, use for every cartridge. |
| Disposable static mixer nozzles, pack of 10 | £4.95 | About 50p per nozzle. |
So your first job costs £24 for one cartridge and a gun, and the two nozzles in the box are usually enough for a single session. Your second cartridge costs £9. If you want a spare supply of nozzles, a pack of 10 is £4.95.
We have not compared our gun with other suppliers' guns here, because prices vary and the guns are not always like for like. If you already own a manual 10:1 gun for 50 ml cartridges, check that it suits the cartridge before you buy another. For the wider picture on adhesive prices, see our guide to how much solid surface joint adhesive costs in the UK.
Do you need a new nozzle every time?
Yes, for each session. The adhesive starts to cure inside the nozzle, and the iSeam Pro 67 technical data sheet gives a working time of 9 to 11 minutes. Once you stop for longer than that, the mixed material in the nozzle will set. Fit a fresh nozzle for the next use, and discard the first couple of centimetres of material that comes out so you start with a properly mixed bead. That is why we include two nozzles with each cartridge and sell packs of 10 separately.
Is a manual gun good enough?
For a kitchen worktop joint or a repair, yes. A manual gun gives you control, and the seam is a short, careful job rather than a production run. Pneumatic guns exist and suit workshops making many joints a day, but you do not need one for occasional work.
What if you only have one joint to make?
Be realistic about the numbers. If this is a single seam, the £15 gun is more than the adhesive itself, and that can feel like poor value. There is no way round the 10:1 cartridge format, so your options are to buy the gun and keep it for future repairs, to borrow a 10:1 gun from a friend or fabricator, or to ask whoever is installing the worktop to make the joint. If you are comparing a one-off against cheaper options such as superglue or epoxy, read superglue vs epoxy vs seam adhesive first, because a visible or weak seam costs far more to put right than a £15 gun.
What else should you have ready?
- Clean, dry, dust and grease free surfaces. The data sheet is clear that bonding depends on this.
- An application temperature between +5 and +35 °C.
- Clamps, and time to work inside the 9 to 11 minute working time.
- Sandpaper. The joint can be sanded after 30 minutes, with full cure at 24 hours.
Remember that the cure is exothermic, so keep to thin joint lines rather than building up thick sections. The data sheet gives a gap fill of 1 to 2 mm.
Safety note: Part A contains methyl methacrylate (highly flammable, can irritate or sensitise skin). Use gloves, eye protection and good ventilation, and read the safety data sheet first.
What should you do next?
Work out your total before you order: one iSeam Pro 67 cartridge at £9, plus a 10:1 gun at £15 if you do not already have one. Read the iSeam Pro 67 technical data sheet on the product page so you know the working time, cure times and temperature limits. If you are not sure the colour will match your worktop, or you are unsure about your material, email us at sales@gludog.com before you buy and we will help. Our earlier post on the best adhesive or sealant for Corian is also a useful starting point.