Formoa 063 white sealant and construction adhesive 290ml cartridge

Formoa 063 vs Silicone: Which Caravan Sealant Should You Use on Vans, Caravans and Boats?

The short answer: for sealing and bonding on vans, trailers, caravans, motorhomes and boats, an MS polymer caravan sealant such as Formoa 063 is usually the better choice than silicone. It sticks harder, can be painted, stays white outdoors and also works as a light-duty adhesive. Silicone still wins on price, on very high temperatures and on ease of finishing. This post is for anyone choosing a sealant for vehicle, caravan or marine work, whether you build them for a living or you're repairing your own.

Formoa 063 white sealant and construction adhesive 290ml cartridge

What is the real difference between Formoa 063 and silicone?

Both are one-part sealants that come in a cartridge and cure from moisture in the air. The difference is in the chemistry. Silicone is built for sealing: it is very flexible and easy to work, but it has little grab or strength. Formoa 063 is an MS (silane-modified) polymer made by Forgeway. It seals, and it also bonds panels, trims and floors. That's why it's sold as a "3-in-1" sealant and construction adhesive. If MS polymers are new to you, our earlier post What is an MS polymer adhesive, and what does it cost in the UK? covers the basics.

How do they compare side by side?

The 063 figures come from the Formoa 063 technical data sheet. Silicone figures vary by brand, so the silicone column gives the general picture from Forgeway's silicone vs MS polymer guide.

Question Formoa 063 (MS polymer) Typical silicone
Will it bond as well as seal? Yes: 3 N/mm² tensile, 2 N/mm² shear strength. Fine for light panels, trims and floors, but not structural Seals only; little grab or bond strength
How far does it stretch? Over 480% elongation at break Very flexible
Can you paint over it? Yes, with many paints (do a compatibility test first) No, paint won't stick to it
Will it go yellow? Stays white: colour change under UV testing of less than 1 (ΔE) Depends on the grade
Will it go mouldy? Better mould resistance than cheap silicone, according to Forgeway Cheap grades can mould within months in damp conditions
Heat resistance MS polymers aren't suitable above about 150°C Up to about 250°C
Ease of finishing Thick (high grab), so it takes more practice Easy, even for beginners
Glazing? No: the data sheet says it can't be used as a glazing sealant Some grades are made for glazing
Price £7.75 (290ml), £13.14 (600ml) at Gludog, checked November 2026 Cheaper; Forgeway mentions budget tubes at around £3

Why is silicone a poor choice on vans, caravans and boats?

Three reasons come up again and again.

  • It doesn't hold anything. On a vehicle or a boat, a sealed joint usually also has to keep a trim, panel or fitting in place while everything vibrates. Silicone isn't designed to do that. Formoa 063 has a high grab, so parts stay where you put them while it cures.
  • Nothing sticks to it afterwards. Paint won't take over silicone. Once silicone has been on a surface, the residue can also stop new sealant or paint bonding. Getting it all off later is a slow job.
  • It can look tired quickly. Cheap silicones can pick up dirt and mould in damp conditions. If your caravan sealant already looks grubby, our post Why does the sealant on my caravan look dirty? explains why.

What is Formoa 063 used for?

Forgeway lists jobs like sealing inside and outside commercial vehicles, bonding trailer floors, bonding and sealing caravans and motorhomes, bonding floors in static caravans and cabins, and sealing yacht interiors and exteriors. It is primerless on most clean surfaces. Forgeway says it has good adhesion to plastics such as ABS, PVC and acrylics as well as metals. Plastics vary by maker, so the data sheet recommends testing on your own material first. On non-porous surfaces you can use Formoa Surface Activator to give the bond extra security.

It also cures without shrinking (less than 1% volume change), cures through at about 3.5mm per 24 hours and comes in white, grey, black and brown.

Is Formoa 063 harder to apply than silicone?

Yes, a bit. This is the main objection, and it's fair. 063 is thick, which gives the high grab, but it doesn't flow as easily as silicone. In Forgeway's own review of 063, a marine customer praises its instant grab and stay-white finish, but says the thickness can make a good finish harder and suggests some training for first-time users.

That said, 063 finishes more smoothly than most MS polymers. Some tips that help:

  • Work at between 10°C and 30°C (the data sheet's application range).
  • Tool the bead with a soapy solution before it skins. Skin time is about 16 minutes, with a maximum open time of 30 minutes.
  • Clean up wet sealant straight away with white spirit or Formoa Surface Cleaner. Once it has cured, it has to be cut away.
  • For long runs, a 600ml sausage in a good gun gives you a steadier bead than a 290ml cartridge.

Our older guide How to create a good smooth finish with an MS polymer goes into more detail.

When should you still use silicone, or another product?

We'd rather you used the right product than bought ours for the wrong job.

  • Silicone is the better pick where the joint gets hotter than about 150°C, or for a cheap, seal-only joint indoors where nothing needs to be painted or bonded.
  • Glass bonding: 063 isn't a glazing product. For bonded windows on coaches, minibuses and boats, look at Formoa 055, a primerless direct-glazing adhesive.
  • Heavier bonds: 063 isn't structural. For panels that carry load or vibration, Formoa 017FE is one of the strongest one-part MS polymer adhesives available. For rigid, very high-strength joints, an epoxy or a Purok or Aerok MMA adhesive is a better fit.
  • Low-energy plastics such as polypropylene and polyethylene need extra preparation, such as Formoa Primer PP. Don't rely on 063 alone.

How much does it cost?

At Gludog (prices inc. VAT, checked November 2026):

A silicone tube costs less on the shelf. But if it fails, needs redoing, or stops paint or a new sealant from sticking, it can cost you more in labour than it saved.

Is it safe to use?

Like every Formoa product, 063 is isocyanate-free and UV stable. Still, read the safety data sheet before you use it, wear gloves and work in a ventilated space.

What should you do next?

If you're replacing old silicone, remove all of it and clean the surface well first. Silicone residue stops MS polymer bonding reliably. Then read the Formoa 063 data sheet, and try a test bead on your own material before the full job. If you're not sure whether 063, 017FE or 055 suits your joint, email us at sales@gludog.com. Tell us the materials and the job, and we'll give you a straight answer.

Back to blog